Specialty Safety Cleaner
Rivolta S.L.X. 500 is a specialty safety cleaner designed for challenging cleaning tasks in electronics and mechanical engineering.
K2: describes solvent-based cleaning products for electrical and electronic equipment and instruments.
Rivolta S.L.X. 500 is recommended for cleaning highly sensitive electronic systems, components, and equipment while they are energized (AuS). Cleaning no longer requires powering down or disassembly. When working on live equipment, please be sure to follow DIN VDE 0105-100 “Operation of Electrical Systems”!
S.L.X. 500 is non-flammable (no flash point) and has a very high dielectric strength. This special cleaner can therefore also be used on live electrical systems that are in operation. Shutting down the system is not necessary, which leads to cost savings by reducing the downtime that would otherwise result from a shutdown. Another advantage is the cleaning agent’s very rapid evaporation. No disruptive residues remain, and the adhesion of new dirt is prevented. The minimal drying time ensures shorter service intervals.
The special safety cleaner is characterized by excellent material compatibility and does not attack common metals, contact coatings, insulation, paints, varnishes, rubber, plastics, etc. All components, regardless of material type (metals, non-ferrous metals, plastics, and elastomers), can be treated without restriction. S.L.X. 500 cleans effectively and thoroughly due to its low surface tension and high specific gravity. This allows the cleaner to penetrate even the tiniest microscopic cracks and crevices. The liquid medium reaches hard-to-access areas within the system. The cleaner thoroughly washes over the components, removing dusty as well as lightly oily and greasy contaminants. The resistance values of insulating materials and/or the conductivity of, for example, contact materials, etc., are improved or restored.
Applications
Rivolta S.L.X. 500 is used for cleaning systems and devices in measurement, regulation, and control technology; electromedical equipment; electronic devices and systems; ICs; circuit boards; memory modules; PLCs; microcontrollers; processors; sensors; pressure control panels; photocells, optical systems, magnetic heads, measuring instruments, amplifiers, collectors, contacts, potentiometers, relays, switches, clock mechanisms, counters, etc.
Application Instructions
Apply using a spray can, spray, immersion bath, or brush. Excellent cleaning results are achieved when Rivolta S.L.X.
500 is applied using a B&L high-pressure cleaning device. S.L.X. 500 can also be used in an ultrasonic bath.
You can find suitable application equipment and accessories in our product range.
Do you need more information about our products or applications? Then just get in touch with us!
Finish cleaner
Specialised Cleaning Concentrate
Hot-melt remover
Specialised Adhesive Remover
Wet wipes
Specialised cleaning product for wind turbines and industrial plants
Directions to Bremer & Leguil
By car
Take Exit 13 (DU-Wanheimerort) off the A59. If you’re coming from Duisburg, turn right. If you’re coming from Düsseldorf, turn left. You are now on Wacholderstraße; follow this street. At the second traffic light, turn left onto Düsseldorfer Straße. Follow the road for about 1.5 km. At the traffic light, turn right onto Neuenhofstraße. Continue straight through the next intersection. After about 300 meters, you’ll see the Bremer & Leguil warehouse at number 101 on the left.
Note on entering the address into your navigation system:
Please enter “Neuenhofstraße 90” into your navigation system, as the correct house number, 101, leads to a gated entrance.
Directions to Bremer & Leguil
By train
Bremer & Leguil is a 10-minute walk from the train station. From the main exit, cross the station forecourt and turn right onto Mercatorstraße. Then turn left onto Königsstraße (pedestrian zone). At the “Lifesaver” fountain, turn right onto Am Burgacker. After crossing at the traffic lights, Bremer & Leguil is 50 meters further on the right-hand side.
By car
From Düsseldorf:
Take Exit 10 (DU-Duissern) off the A59. Turn right and follow the road. At the next traffic light, turn right onto Landfermannstraße. Follow the road and, after the third traffic light, turn right onto “Am Burgacker.”
From Dinslaken:
Take Exit 10 (DU-Duissern) off the A59. Turn right and follow the road until you reach the third street on the left. Turn onto Moselstraße there. At the next intersection, turn right onto Fuldastraße. After about 100 meters, turn left onto “Am Burgacker.”
Directions to Bremer & Leguil
By car
Take Exit 13 (DU-Wanheimerort) off the A59. If you’re coming from Duisburg, turn right. If you’re coming from Düsseldorf, turn left. You are now on Wacholderstraße; follow this street. At the second traffic light, turn left onto Düsseldorfer Straße. Follow the road for about 1.5 km. At the traffic light, turn right onto Neuenhofstraße. Continue straight through the next intersection. After about 300 meters, you’ll see the Bremer & Leguil warehouse at number 101 on the left.
Note on entering the address into your navigation system:
Please enter “Neuenhofstraße 90” into your navigation system, as the correct house number, 101, leads to a gated entrance.
You are currently viewing a placeholder content from Vimeo. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from YouTube. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More InformationYou need to load content from reCAPTCHA to submit the form. Please note that doing so will share data with third-party providers.
More InformationYou are currently viewing a placeholder content from reCAPTCHA. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.
More Information
